Coupling GEOS-Chem with RRTMG
The GEOS-Chem model with online radiative transfer calculations (referred to as GCRT) was developed to allow GEOS-Chem users to produce gas and aerosol direct radiative effect (DRE) output. This alternative to offline coupling allows better temporal resolution in the RT calculations and provides a consist platform for GEOS-Chem users with the widely used radiative transfer package RRTMG.
Most of the added code is 'transparent', therefore this version of the GEOS-Chem model can still be run with the radiation code switched off. The optical properties are calculated at multiple wavelengths so the user is no longer restricted to 550nm as default, so there are associated changes regardless of whether the radiative code is invoked. However, these cause negligible slow down (the default model is actually slightly faster). Compiling with RRTMG=yes requires approximately double the amount of RAM (~15Gb for a 2x2.5 simulation) and takes between 40% and 100% longer depending on the settings used.
This wiki explains the key changes and requirements and links to the documentation for getting started running the model, digging deeper into the changes and assumptions made. [link]
Authors and collaborators
- Colette Heald (Civil and Environmental Engineering, MIT) -- Principal Investigator
- Steven Barrett (Aeronautics and Astronautics, MIT)
- David Ridley (Civil and Environmental Engineering, MIT)
- Karen Cady-Pereira (AER)
- Matthew Alvarado (AER)
Questions regarding GCRT can be directed at David (e-mail linked above).
--David R. 18:00, 08 October 2013 (EST)
GCRT User Groups
|Atmospheric Chemistry, Massachusetts Institute of Technology||Colette Heald
| GCRT Publication |
Inter-annual variability and trends in African dust
Modeling black and brown carbon
|Add yours here|
1. A new menu for Radiation exists in input.geos (see below). This also includes a wavelength selection for optical depth output that is independent of whether RRTMG is switched on (up to three optical depths can be output in the standard OD-MAP-$ diagnostic, but only the first is used for diagnostics other than the standard bpch output e.g. ND51).
2. A new code folder, GeosRad/, is required for the RRTMG code. The module "rrtmg_rad_transfer_mod.F" is the driver code (within GeosCore/) that interfaces with RRTMG.
3. The optics look-up tables are updated, containing multiple wavelengths and separated into files for each species (soot.dat, so4.dat, org.dat, dust.dat, ssa.dat, ssc.dat) that are stored in the run directory. To prevent discrepancies jv_spec.dat no longer contains optical properties for aerosol, Fast-J uses optics from from the same speciated look-up tables. The new files mean that jv_spec_aod.dat is redundant and no longer used.
4. Several new input files are required. Surface albedo and emissivity climatologies have been generated and must be stored in modis_surf_201210/ within the root data directory (e.g. GEOS_2x2.5/). Climatologies of gases (CH4, N2O, CFC-11, CFC-12, CFC-22 and CCl4) must be stored within the root data directory.
5. A new set of diagnostics (ND71) are available providing the change in radiative flux (DRE) for gases and aerosol, LW/SW, top of atmosphere (TOA) and surface, and clear-sky and all-sky conditions. These also include AOD, SSA and asymmetry parameter for each aerosol species at the requested wavelengths.
As with the latest version of GEOS-Chem, NetCDF libraries must be installed (see Installing libraries for GEOS-Chem). The code should be compiled using the compile switch RRTMG, i.e. "make RRTMG=yes". A fresh compilation after a "make realclean" will take 15-20 mins (subsequent compiles are much faster).
Once the code is compiled the input.geos file will need configuring:
%%% RADIATION MENU %%% :
AOD Wavelength (nm) : 550 440 532
Turn on RRTMG? : T
Calculate LW fluxes? : T
Calculate SW fluxes? : T
Clear-sky flux? : T
All-sky flux? : T
Radiation Timestep [min]: 180
Species fluxes : 0 0 1 0 0 0 0 0 0 1
The species for which DRE output is currently available are listed with two-letter identifiers. In the example the DRE is calculated for sulfate (SU) and all particulate matter (PM) - see the table below for all identifier descriptions. The radiation time step defaults to 180 mins but can be set for any multiple of the chemistry time step. The baseline (BA) flux is always output by default and is the flux (W/m^2) with all aerosol and species included.
In this set up all diagnostics from ND48 to ND51b produce optical depth output at 550nm, but the main diagnostic output contains three copies of the optical depths (and SSA and asymmetry parameters if requested). The output variables have the wavelength appended to the variable name e.g. OPBC550.
All particulate matter
The ND71 diagnostic must be set to 1 if RRTMG is switched on.
Once all the auxiliary files are in place and the input.geos set up the model can be run in the usual way.
For more information please consult the documentation [link]