GFED4 biomass burning emissions
GFED4 biomass burning emissions are now included in GEOS-Chem v10-01 and higher versions.
Contents
Source code and data
GFED4 was implemented into GEOS-Chem v10-01 as an extension of the HEMCO emissions component. The source code files may be found in the GEOS-Chem source code folders:
File | Description |
---|---|
HEMCO/Extensions/hcox_gfed_mod.F90 | Module for computing GFED4 biomass emissions |
HEMCO/Extensions/hcox_gfed_include_gfed4.H | Emission factors for GFED4 species (inlined for computational efficiency) |
We have created new GFED4 data files (in COARDS-compliant netCDF format) for use with HEMCO. These new data files are contained in the HEMCO data directory tree. For detailed instructions on how to download these data files to your disk server, please see our Downloading the HEMCO data directories wiki post.
--Bob Y. (talk) 15:53, 17 June 2015 (UTC)
Discussion following 1-month benchmark v10-01h
GFED4 biomass burning emissions were validated in GEOS-Chem v10-01h. The following discussion ensued.
Prasad Kasibhatla wrote:
- I have been looking at the CO biomass emission ratio plot in the 10-01h benchmark - there are a couple of regions where things look a bit different than what I expect from the emissions I compute offline at native resolution. Would it be possible for you to send me plots of absolute CO emissions from biomass burning from v10-01h and v10-01f_UCX that went into the ratio plot. And a difference plot?
Melissa Sulprizio wrote:
- Please see the attached image for maps of CO biomass emissions from v10-01f_UCX (upper left) and v10-01h (upper right). The absolute difference (lower left) and percent difference (lower right) maps are also included.
Prasad Kasibhatla wrote:
- I computed CO emissions offline for GFED3 for July 2011 and GFED4 for July 2013 (corresponding to what was used in the v10-01f_UCX and v10-01h benchmark runs) and reproduced the emissions plot you sent.
- Don't worry about the labels on my plot - my panels correspond to your panels. As you can see your patterns match patterns I compute - but absolute values of emissions that you are getting from the model are higher than what I calculate offline. I have not been able to figure out if I am making a mistake in my offline calculation or if there is a problem in the geoschem implementation.
- Obviously, we need to figure this out. Perhaps Christoph and I can focus on one or two pixels and resolve what is going on?
- For both the GFED3 and GFED4 offline plots, I accumulated dry matter burned in various categories into the generic 1x1 grid, computed emissions in molecules/cm2 on the 1x1 grid using category-specific emission factors, and then regridded to the 4x5 grid using ctm_regridh with the /per_unit_area option.
Christoph Keller wrote:
- Thanks, this may explain it. In v10-01e and newer, dry matter burned and vegetation mask are first regridded onto the simulation grid, and emissions are computed on that grid.
- I looked into this for version v10-01e, and the changes in GFED-3 emissions (compared to pre-HEMCO versions) are attributable to the regridding order. In v10-01h, we didn’t change anything in GFED-3, and GFED-4 uses the same code as GFED-3 except for the updated dry matter emissions fields.
--Melissa Sulprizio 13:38, 27 March 2015 (EDT)
References
- GFED website: http://globalfiredata.org
- Akagi, S. K., R. J. Yokelson, C. Wiedinmyer, M. J. Alvarado, J. S. Reid, T. Karl, J. D. Crounse, and P. O. Wennberg, Emission factors for open and domestic biomass burning for use in atmospheric models, Atmos. Chem. Phys., 11, 4039-4072, 2011. Article
- Andreae, M. O., P. Merlet, Emission of trace gases and aerosols from biomass burning, Glob. Biogeochem. Cycles, 15, Issue 4, pages 955-966, December 2001. Article
- Giglio, L., J. T. Randerson, and G. R. van der Werf, Analysis of daily, monthly, and annual burned area using the fourth-generation global fire emissions database (GFED4)", J. Geophys. Res, Biogeosciences., 118, Issue 1, 317-328, March 2013. Article
- Randerson, J. T., Y. Chen1, G. R. van der Werf, B. M. Rogers, and D. C. Morton, Global burned area and biomass burning emissions from small fires, J. Geophys. Res, Biogeosciences, 117, Issue G4, December 2012. Article
- van der Werf, G. R, J. T. Randerson, L. Giglio, G. J. Collatz, M. Mu, P. S. Kasibhatla, D. C. Morton, R. S. DeFries, Y. Jin, and T. T. van Leeuwen, Global fire emissions and the contribution of deforestation, savanna, forest, agricultural, and peat fires (1997-2009) Atmos. Chem. Phys., 10, 11707-11735, 2010. Article
--Bob Y. 10:56, 17 March 2015 (EDT)
Previous issues that are now resolved
Fixed unit conversion error on 18 Jun 2015
On 18 Jun 2015, we fixed a unit conversion error in the GFED4 data files that were contained in the HEMCO data directory GFED4/v2015-06/:
Zhen Qu wrote:
- The biomass burning emission seems to be smaller by about 3 magnitude with the conversion error.
Christoph Keller wrote:
- Yes, this sounds about right. The GFED-4 netCDF files that we use in GEOS-Chem are directly generated from the original GFED-4 data. These data changed units between the provisional and the official GFED 4 release (gDM/m2/month to kgDM/m2/month). I didn’t realize that and the GFED-4 files were hence a factor of 1000 too low.
The GFED4 data files with the correct units were uploaded to the HEMCO data directory tree at 4PM EDT on 18 Jun 2015. If you obtained GFED4 data prior to 18 Jun 2015, we ask you to re-download this data.
To download the data, you can use the hemco_data_download installer, as described on our Downloading the HEMCO data directories wiki post. Or if you would like to get these files directly, you can use this FTP command:
ftp "ftp://ftp.as.harvard.edu/gcgrid/data/ExtData/HEMCO/GFED4/v2015-06/*.nc"
We apologize for the inconvenience.
--Bob Y. (talk) 20:11, 18 June 2015 (UTC)
Currently unresolved issues
None at this time.
--Bob Y. 14:27, 27 March 2015 (EDT)